Blown Film Extrusion Introduction

Blown Film Extrusion Introduction
Blown film extrusion is a technology that is the most common method to make plastic films, especially for the packaging industry. The process involves extruding a tube of molten polymer through a die and inflating to several times its initial diameter to form a thin film bubble. This bubble is then collapsed and used as a lay-flat film or can be made into bags. Usually polyethylene is used with this process, and other materials can be used as blends with these polymers. A diagram of a polyethylene chain is shown in Figure 1 to the right.
Background Theory on Polymers

In the cooling step of blown film extrusion, the amorphous, transparent melt crystallizes to form a translucent, hazy, or opaque film. The point where opacity begins in the bubble is known as the frost line. 
Fig 1: Model of polytheylene chain frompolyethylene Wikipedia article.The frost line height is controlled by several parameters: the air flow, film speed, and temperature difference between the film and the surroundings. Properties of the film, such as tensile strength, flexural strength, toughness, and optical properties, drastically change depending on the orientation of the molecules. As the transverse or hoop direction properties increase, the machine or longitudinal direction properties decrease. For instance, if all the molecules were aligned in the machine direction, it would be easy to tear the film in that direction, and very difficult in the transverse direction.

The Film Blowing machine Process

Fig 2: Schematic of set-up from User:J.Chiang.

Typically, blown film extrusion is carried out vertically upwards, however horizontal and downward extrusion processes are now becoming more common. Figure 2 shows a schematic of the set-up for blown film extrusion. This procedure consists of four main steps: The polymer material starts in a pellet form, which are successively compacted and melted to form a continuous, viscous liquid. This molten plastic is then forced, or extruded, through an annular die. Air is injected through a hole in the center of the die, and the pressure causes the extruded melt to expand into a bubble. The air entering the bubble replaces air leaving it, so that even and constant pressure is maintained to ensure uniform thickness of the film. The bubble is pulled continually upwards from the die and a cooling ring blows air onto the film. The film can also be cooled from the inside using internal bubble cooling. This reduces the temperature inside the bubble, while maintaining the bubble diameter. After solidification at the frost line, the film moves into a set of nip rollers which collapse the bubble and flatten it into two flat film layers. The puller rolls pull the film onto windup rollers. The film passes through idler rolls during this process to ensure that there is uniform tension in the film. Between the nip rollers and the windup rollers, the film may pass through a treatment centre, depending on the application. During this stage, the film may be slit to form one or two films, or surface treated. Advantages Blown film generally has a better balance of mechanical properties than cast or extruded films because it is drawn in both the transverse and machine directions. Mechanical properties of the thin film include tensile and flexural strength, and toughness. The nearly uniform properties in both directions allow for maximum toughness in the film.
Blown film extrusion can be used to make one large film, two smaller ones, or tubes that can be made into bags. Also, one die can make many different widths and sizes without significant trimming. This high level of flexibility in the process leads to less scrap material and higher productivity. Blown films also require lower melting temperatures than cast extrusion. Measured at the die opening, the temperature of cast film is about 220 C, where as the temperature of blown film is about 135 C. Furthermore, the cost of the equipment is approximately 50% of a cast line.

Blown Film Extrusion Disadvantages Blown film has a less effective cooling process than flat film. Flat film cooling is done by means of chill rolls or water, which have significantly higher specific heat capacities than the air that is used in the blown film cooling process. The higher specific heat capacity allows the substance to absorb more heat with less change in the substance temperature. Compared to cast film, blown film has a more complicated and less accurate method to control film thickness; cast film has a thickness variation of 1 to 2% versus the 3 to 4% for blown film. The resins used for casting typically have a lower melt flow index, which is the amount of polymer that can be forced through a standard die in 10 minutes according to a standard procedure. The melt flow index for cast film is about 5.0 g/10 min where as for blown film it is about 1.0 g/10 min. Consequently, the production rates for cast film are higher: cast film lines can reach production rates of up to 300m/min where as blown film lines are usually less than half this value. And finally, cast film has better optical properties, including transparency, haze, and gloss.

Common Problems Air entrapment between film layers and rollers – this may cause film scratching or wrinkling, or processing problems when winding up the film due to reduced friction. Possible solutions to this is using a vacuum to remove entrapped air or by using winding rolls with a diamond shaped groove in the rubber cover to increase surface area and decrease amount of entrapped air in the film. Large output fluctuations from the die – this causes thickness variations, and can be prevented by keeping the extruder clean and by using more consistently shaped pellets in the extruder. Melt fractures – these appear as roughness or wavy lines on the film surface, and can be eliminated by lowering the viscosity of the polymer melt. This can be done by increasing the melting temperature or by adding an internal lubricant to the material composition. Thickness variations in the film – this can be avoided by centering the die in the extrusion line before every run, adjusting the air speed of the cooling system, or by using heated die lips. Die lines on the surface of the film – this defect reduces the aesthetic appeal of the film, reduces optical properties, and weakens mechanical properties such as tear strength. This can usually be avoided by routinely cleaning the inner surfaces of the die and by refinishing scratched or roughened flow surfaces. Gels – these defects are small, hard globules encapsulated in the film or stuck on the film surface and reduce the aesthetic appeal of the film and cause stress concentration points which may result in premature failure. These are caused by overheating to the point of polymer degradation in the die, and can therefore be avoided by cleaning the inner surfaces of the die on a regular basis. Optimization of the Process Coextrusion One way to improve the line efficiency of blown film extrusion is to implement coextrusion. This is the process of extruding two or more materials simultaneously through a single die. The orifices in the die are arranged such that the layers merge together before cooling. This process saves time because it extrudes two or more layers at the same time, and it provides a method with fewer steps to produce multilayer films. The production rate for a coextruded multilayer film of three layers is about 65m/min, and the production rate for a single layer of blown film is about 130m/min. Thus, in order to produce 10 000m of a three layer multilayer film, it would take almost 4 hours using a single layer blown film process, and only 2 and a half hours using the coextrusion process. Furthermore, the film produced from the single layer process would require an extra step to glue the layers together using some sort of adhesive. Coextrusion is the least expensive means of producing layered films and the coextrusion system is capable of quick changeovers to minimize production line down time.

Minimizing the Melt Temperature
The efficiency of blown film extrusion can be improved by minimizing the temperature of the polymer melt. Reduction of the melt temperature causes the melt to require less heating in the extruder. Normal extrusion conditions have a melting temperature at about 190 C despite the fact that the temperature of the melt only needs to be about 135 C. However, it is not always practical to decrease the melting temperature by that much. By decreasing the melt temperature 2 to 20 C, the motor load can be decreased by about 1 to 10%. Furthermore, reduction of the melt temperature causes less need for cooling, so there is a reduced use of the cooling system. Moreover, removing heat from the bubble is usually the rate-limiting factor in this extrusion process, so by having less heat in the polymer to remove, the rate of the process can be increased, thus yielding higher productivity. A way to maintain the melt temperature at a minimum is to choose an extruder that is matched to the specific processing conditions, such as the material of the melt, pressure, and throughput.

Heated Extrusion Die Lips
Typically, solutions to melt fractures involve decreasing the output or increasing the melt temperature to decrease the shear stress in the extruder. Both of these methods are not ideal because they both reduce the efficiency of the blown film line. Heated extrusion die lips can solve this problem. This targeted heating method allows for film extruders to be run at higher production rates with narrower die gaps while eliminating melt fractures. Direct heat is applied to the surface of the polymer melt as it exits the die so that viscosity is reduced. Therefore, melt fractures, which are caused when trying to extrude too much of the polymer at one time, will no longer act as a limiting factor to increasing the production rate. Furthermore, heated die lips use less energy than increasing the melting temperature because only the surface of the melt is heated and not the bulk of the liquid. Another benefit of using heated die lips is that thickness variations can be controlled by adding heat to certain areas along the die circumference to make the film at that position thinner. This would ensure that no excess material is used.
Determine how much energy each of these processes can save per given volume of material. 

Above article from www.appropedia.org

Kingdom Machine Co.,ltd Ruian Economic Zone,Wenzhou,China 325200
Mobile:0086-13958812663;  0086-13088651008
Tel.:0086-577-65127709       Fax:0086-577-56846789 Whatsapp:0086-13958812663
sale@kingdommachine.com www.kingdommachine.com www.chinablownfilmextrusion.com

Why Weight Reduction is Awesome and Apettite supressant 37.5 mg is Warm?

Many women today have been in a damsel in hardship method, quite definitely a modern day model from the Victorian dames, concerned with their number. The both mental and physical prospect of females have progressed with the passing of time, but specific issues close to their center continue being unrevised. An hourglass shape then is really a pad thin determine now, which has a document 83 Per-cent of woman college students hooked to dieting techniques. They try each trade secrets from skipping breakfast every day and using tobacco to nausea and swallowing weightloss pills in the quest for a thin and stylish search.
Weight-loss is not any far more a problem limited to the obese by yourself, as numerous women use press and memory strategy to (mis)deal with how much with out looking after a hoot to the position of the weight inside the BMI size. The state of affairs just isn’t weight-loss for any healthier conclusion, but a prettier and slimmer stop. With all the youthful female group fed on the diet of cleansing soap operas, they admire the performers for style and diet inspirations. Although it’s no imply feat to attain and reproduce the figure and shape of the display screen goddesses in real life, the women are keener, the greater distinctive and bizarre, the best determine is.
Expectation for any aspiration variety and description hard disks the young lot loco, as they make use of any and every available options to access a pedestal, exactly where they would be the covet of everybody. Trim or stout, it does not matter, as all is here weight-loss with regard to fat loss. Their younger tirade and diatribe is infuriating to the point of complete insanity and profanity. They understand no proper and incorrect, they visualize just the musicians effect of an perfectionist. Manner declaration in schools echos the virtual moderate, in fact it is happening to copy whatever they see on-screen. It makes fat loss a very good proposition on the list of feminine students. It keeps them proceeding.
Determined they are, but profitable they may not be in terms of weight-loss in the totality and total. Only once their efforts at skipping breakfast for the days and a few months at a time, string smoking cigarettes and sickness go to waste, ineffective and in vain, will they know that weight reduction is not any easy. Young good deal does not have any time and patience for wholesome actual workouts. Inform they and them would inform you of the time and space restrictions for these kinds of activities. They love to shed pounds, and not the hard way, all things considered those are the kids of a whole new world, where almost everything arrives engrossed in a package deal.
And yes the current ‘press-button’ way of life considers into it what has youngsters are not unhappy. In arrives Apettite supressants 37.5 milligrams from http://aguirreforgovernor.com, diet weight loss pill to indicate them the best way out with no as much physicality out of the box usually needed for losing weight. With its desire for food quelling characteristics, Apettite supressant 37.5 milligrams  drives aside the hunger quotient in them, making their body weight damage plan a lot easier and successful than skipping meals or cigarette smoking. Phentermine 37.5 mg  is hot asset inside the campus (women rely on them more than their beaus).
Weight loss could be a awesome move to make, and Apettite supressants 37.5 milligrams from http://gettingtherefromhere.info might be a very hot capsule to take, but keep this at the back of the mind that weight reduction is centered on bodily, psychological and faith based wholeness. When you use methods nonresident to your technique for weight loss, you happen to be just supporting yourself crutches instead of learning how to go walking on their own.

Apettite supressants 37.5 mg Weight Loss Suppliments – Frequent Inquiries Clarified

Obese troubles several a individuals nowadays for this can still bring about serious medical conditions such as diabetic issues, cardiovascular problems, anti snoring, despression symptoms, and osteoarthritis. The only way using this dilemma is to control the growing dumbbells using a healthy diet plan, compounded by some very good weight loss supplements plus a strict physical fitness program. Largely, it is this mix that work well for most of us. But, this short article concentrates on the diet pill – organic Apettite supressant 37.5 milligram  – and responses few widespread inquiries that many individuals tend to question so as to comprehend a little more about the medication. We imagine you question also capabilities in the answers below.
Precisely what is Organic Apettite supressants 37.5 milligram from http://phentermine.tv-gossip.com?
Herbal Apettite supressants 37.5 mg  is a No Health professional prescribed Phentermine 37.5 milligrams  that is very organic and natural. It can be identified to stimulate number of or no side effects inside the user’s physique. It achieves results by curbing urge for food and escalating metabolic process, thus using up away people extra calories.
Which are the elements of plant based Phentermine 37.5 mg ?
The conventional elements of organic Apettite supressant 37.5 milligram  are Acetyl D-Carnitine, Camellia Sinensis, Green Tea, Acid, Piper Nigrum, Bioperine, Alpha dog Lipoic, and Biotin.
What is the recommended dosage of natural Apettite supressant 37.5 mg ?
A single capsule each day along with the afternoon. In the event you produce any discomfort, decrease the serving to one.
Include the connection between herbal Apettite supressants 37.5 milligrams  temporary?
To a extent, indeed! Although taking herbal Phentermine 37.5 milligrams from http://phentermine.veteransunemploymentbook.com, you won’t feel that significantly famished, which regularly usually takes one to the situation of food craving. But, as soon as the organic Apettite supressant 37.5 milligram  intake is ceased, it’s likely that there that the individual may possibly go back to the existing practice of pigging out as the physique yet again starts to respond to victuals like it used to just before. Hence, in the event you cease herbal Apettite supressant 37.5 milligram  after losing weight, much better learn to overcome your intuition that plead for a tummy total daily.
Which are the benefits of natural Apettite supressant 37.5 milligrams ?
The key as well as with organic Phentermine 37.5 mg  is that it must be totally free of damaging chemical substances or substances like Citrus fruit aurantium or Ephedrine. It is probably the safest normal slimming capsules on the market.